The Dap-1530 setup can be done using the default web address dlinkap.local. You must have a wireless router to connect your Dlink extender to your router’s network. Furthermore, you must be aware of the location where you are experiencing dead zones. Once you set up your D-Link range extender, you can also go about the Dap-1540 firmware update. Updating the firmware of your extender allows you to keep your device up-to-date and stable.
The online web interface makes it extremely simple to set up the Dlink WiFi range extender. The Dlink extender now has its own web interface. D-Link has come a long way in terms of enhancing its web interface and general user experience. Even a novice with no networking experience can quickly complete the extender’s first configuration.
In this post, we will first discuss the DAP-1530 setup and configuration. After that, we will walk you through the DAP-1530 firmware update. In case you fail at any step, you can go about the DAP 1530 reset process that will be mentioned at the end.
Steps to Prepare For the DAP-1530 Setup
This section carries certain instructions that are listed to help you learn how to prepare for the D-Link Extender Setup and installation. Before you perform the setup, it is important that you learn about the basics. We have put down the DAP-1530 setup preparations below for your reference:
- D-Link DAP 1530 WiFi extender
- An existing wireless router
- A smartphone or computer
- An Ethernet cable (optional)
- Stable power supply to the extender
- WiFi credentials of your router
Once you make sure the aforementioned requirements are met, you can proceed with the DAP-1530 setup and installation.
Steps for DAP-1530 Setup and Installation
Now that you are all set for the installation task, you can follow the steps bellow. Make sure you follow the setup instructions very carefully or else you may get caught in the middle of the DAP setup.
- First, connect your extender to a wall socket near your router.
- Only during the setup procedure should you keep your device close to the router.
- Thereafter, turn on your Dlink WiFi extender.
- Connect your computer or laptop to the network of your D-Link range extender.
- After that, launch your preferred web browser.
- In the address bar, type http://www.dlinkap.local and hit enter.
- Next, you will be redirected to the login page. To log in, use the default username and password.
- Finally, the Dlink WiFi extender setup wizard will appear.
- The wizard will assist you in setting up the network of your Dlink extender.
- Finally, follow the on-screen directions to connect the extender to the network of your router.
Now that you have completed the DAP-1530 setup process, you can go ahead with the DAP-1530 firmware update.
How to Perform DAP-1530 Firmware Update?
The firmware update task is one of a few important things that you need to do for your extender. Updating the firmware of your Dlink DAP extender ensures to keep your device optimized, stable, and compatible with latest technologies. The latest firmware version comes with a lot of enhancements, performance improvements, and bug fixes.
Here are a few steps that you need to perform in order to go about the DAP-1530 Firmware Update on your Dlink Extender:
- Firstly, make sure the Dlink extender is connected to the power supply.
- Secondly, connect your computer to the extender’s network.
- You can either use an Ethernet cable or WiFi network.
- For firmware update process, we suggest that you use an Ethernet cable for wired connection.
- Open a web browser and type www.dlinkap.local in the address bar.
- Hit Enter and you will reach the Dlink DAP login page.
- Enter the username and password of the DAP extender, and click Login.
- Finally, go to the Advanced or Maintenance page.
- Select Firwmare and then follow the on-screen instructions to finalize the DAP-1530 firmware update configuration.
Facing Issues with your DAP-1530 Setup or Firmware Update? Fix here.
In case you encounter certain issues with your extender while attempting to set up the device or update firmware, please follow these troubleshooting steps:
- First of all, make sure you switch the connection from WiFi to wired.
- Use an Ethernet cable connection with your extender to set it up.
- Make sure the web browser of your device is running on the most recent update.
- Enter the default web address www.dlinkap.local in the address bar and hit Enter.
- If you can’t visit the DAP-1530 setup wizard, please disable the firmware or antivirus on your system.
- Try again and check whether the issue persists.
- If the issue persists, use any other device or web browser.
- In case you encounter issues during the DAP-1530 firmware update, reboot your device.
- If rebooting the device does not work, please go about the DAP 1530 reset.
- Press and hold the reset button for a good 10 seconds.
- Release the button and your device will restore the factory default settings.
- Once the DAP 1530 reset completes, reconfigure the extender using the default web address.
- Finally, the issues will go off from your DAP wireless range extender.
Conclusion
This page was all about the DAP-1530 setup and DAP-1530 firmware update. We discussed everything related to these two main topics. While setting up the extender requires an existing wireless network, make sure you have the correct WiFi credentials of your home network with you. If you don’t know the credentials, you won’t be able to set up your extender.
We suggest that you follow the aforementioned steps very carefully. Moreover, we hope this page helped you learn how to set up your Dlink DAP extender and even update its firmware to the most recent version. If you experience any trouble with your device or have any queries, kindly feel free to talk to our support team for more assistance.